# Do I need a data resistor in my blade?

**URL:** <https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980>\
**Category:** Sabers\
**Created:** [September 12, 2023, 9:07pm UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980 "2023-09-12T21:07:21Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Brian\_Eachus](https://crucible.hubbe.net/user_avatar/crucible.hubbe.net/brian_eachus/32/2976_2.png) [@Brian\_Eachus](https://crucible.hubbe.net/u/Brian_Eachus)\
**Post date:** [September 12, 2023, 9:07pm UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980/1 "2023-09-12T21:07:21Z")

</div>

The only blades I’ve built personally have been using KR V2 pixel sticks, and there was no additional resistor required inside the blade itself.

Now I’m repairing a blade built by someone else that uses the traditional method of gluing 2 strips together. The blade PCB has a resistor on it.

The amount of glue leftover and some minor damage incurred in the process of removing the PCB makes me just want to use a new one.

My question is, since my data line is already resistored inside my saber(data1), is it necessary to add another resistor up on the new blade PCB?

---

<div class="post-metadata">

**Author:** ![DudeFromOz](https://crucible.hubbe.net/user_avatar/crucible.hubbe.net/dudefromoz/32/3727_2.png) [@DudeFromOz](https://crucible.hubbe.net/u/DudeFromOz)\
**Post date:** [September 12, 2023, 9:20pm UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980/2 "2023-09-12T21:20:33Z")

</div>

Nope, no need if you’re only going to use it with sabers you know already have the resistor either on the data pin on the board or on the in hilt pcb

---

<div class="post-metadata">

**Author:** ![Brian\_Eachus](https://crucible.hubbe.net/user_avatar/crucible.hubbe.net/brian_eachus/32/2976_2.png) [@Brian\_Eachus](https://crucible.hubbe.net/u/Brian_Eachus)\
**Post date:** [September 12, 2023, 9:32pm UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980/3 "2023-09-12T21:32:09Z")

</div>

Ok, that makes sense.

New question then, if it has an SMD footprint, do I need to bridge it? I have a few Shtok V2.5 blade PCBs laying around.

If that’s the case, I might as well just hot air a resistor on.

---

<div class="post-metadata">

**Author:** ![DudeFromOz](https://crucible.hubbe.net/user_avatar/crucible.hubbe.net/dudefromoz/32/3727_2.png) [@DudeFromOz](https://crucible.hubbe.net/u/DudeFromOz)\
**Post date:** [September 13, 2023, 1:00am UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980/4 "2023-09-13T01:00:31Z")

</div>

Yeah you need to bridge the pads if not using a resistor so if you’ve got resistors might as well put one on. A few in line won’t hurt

---

<div class="post-metadata">

**Author:** ![Brian\_Eachus](https://crucible.hubbe.net/user_avatar/crucible.hubbe.net/brian_eachus/32/2976_2.png) [@Brian\_Eachus](https://crucible.hubbe.net/u/Brian_Eachus)\
**Post date:** [September 13, 2023, 1:03am UTC](https://crucible.hubbe.net/t/do-i-need-a-data-resistor-in-my-blade/3980/5 "2023-09-13T01:03:29Z")

</div>

Awesome. Thank you.
